AUTONET TV

Not-So-Common Sense (Sensor Failures)

So your vehicle won't start.  What's the first thing that comes to mind?  Battery dead? Starter motor worn out? Out of gas?  Well, those are all reasons that make sense.  But your vehicle may be refusing to start because one of its computers is being warned that to do so might damage it.  Here's how that works.

You have lots of computers in your vehicle.  They need to know the status of things so there are several sensors monitoring various things going on.  These sensors send information to the computers that adjust the fuel and air mixture so you don't waste fuel.  They know when things aren't quite right and prevent you from starting your engine if that's going to damage it. 

Other sensors make sure the coolant is the right temperature, check to see you are not polluting the air and make sure other electronic components are performing their tasks correctly.

Here's an example of a sensor doing its job.  Your engine needs oil to lubricate metal components so the friction doesn't damage them.  Your engine has an oil pressure sensor that tells a computer called the Electronic Control Unit (ECU) if things are good to go or if there's something wrong, maybe the oil pressure is too low to keep things lubricated.  If it is, it gives a signal for the vehicle not to start, protecting the engine. 

Of course, the sensors can go bad, too, with some of the same results.  And so someone has to figure out if it's the sensor that's failed or if it really has detected a problem.  That is the challenge for technicians with specialized equipment to decipher the signs.  If a bad sensor is found, it may need to be replaced.  Sometimes a thorough cleaning can do the trick.  In either case, your service facility can track down the problem and get you back on the road.  Makes sense, doesn't it?

Madison Automotive
2457 Covington Pike
Memphis, TN 38128
(901)386-9600
http://www.madisonautomotive.net

Straight to the Point (Alignment Signs of Problems)

It’s just common sense that your vehicle will drive better if all the wheels are lined up with each other and the road the way the engineers intended.  When they’re not, that is called being out of alignment.   Here are some signs that your alignment has problems.

• Your steering wheel isn’t straight when your vehicle goes straight down a straight road. This one’s pretty easy to notice.  If your vehicle’s logo on the wheel is tilted, that’s probably not the way designers wanted it to be. Bring it in and have us check it out.
• Your steering wheel is vibrating on a smooth road or when you are accelerating.  While this could be caused by several different things, one possibility is misalignment.  If your steering wheel is shaking, it should be examined by a trained technician.
• Your vehicle is pulling to one side without you wanting it to.  Sometimes the configuration of the road will cause it to pull slightly left or right.  But if you find yourself constantly correcting course to keep your vehicle headed straight down the road, that’s worth having us look at your alignment.
• You’re going through tires like there’s no tomorrow. The tread on your tires should be wearing nice and evenly from the outside to the inside of the tire.  If the wear isn’t even, it could be your vehicle needs an alignment.

We have equipment designed to quickly and accurately measure your vehicle’s alignment.  We can make precise adjustments to make sure you are headed straight where you want to go.  Have your alignment checked regularly. It can help prevent more serious problems in the future and make your vehicle drive as beautifully as you remember it used to.

Madison Automotive
2457 Covington Pike
Memphis, TN 38128
(901)386-9600
http://www.madisonautomotive.net

Reaching the Braking Point (Brake hose replacement)

If you notice your brakes aren’t working like they used to, that’s the kind of thing that’s important to have checked out soon.  That’s because your brakes are extraordinarily important to the safe operation of your vehicle. 

Sometimes you feel like your brake pedal is feeling a little soft or it’s lower than usual. Or you might feel like the brakes are on all the time, holding you back. Maybe when you release the brake pedal, it comes back up more slowly than usual. There are a few different problems that can cause your brakes to feel like any of those things, so bring your vehicle in to us and we can inspect them.

One possible cause of those brake issues is a damaged or worn-out brake hose.  Your hydraulic brakes work by carrying brake fluid to each of your wheels.  There are steel lines that carry the fluid most of the way, but because your wheels are moving all the time, a flexible hose is used to connect the steel lines and the brakes themselves.  

Sometimes those brake hoses leak, since there’s a lot of pressure inside when you use your brakes dozens or hundreds of times a day.  Road debris, aging, and corrosion at the hose fittings can loosen up that connection.  Sometimes the hoses can get blocked up if the interior lining separates from the outside. And sometimes, it’s simply a matter of the hose getting too old, and age eventually causes the rubber to fail.

When you experience brake problems, bring your vehicle in so we can have a technician take a look. Visual and manual inspections can usually pinpoint the problem areas.  The technician will look for corrosion and physical damage, plus run a pressure check.

For your vehicle to be safe on the road, your brakes need to be working the way they were designed to.  Stop. And think about it!

Madison Automotive
2457 Covington Pike
Memphis, TN 38128
(901)386-9600
http://www.madisonautomotive.net

Beginning to See the Light (Check Engine Light Diagnostics)

It's a light many drivers fear they'll see turn on at the most inopportune time.  It's the one on the dash that says "Check Engine," "Service Engine Soon," or it may be simply an engine-shaped light. Your first instinct may be to pull off to the side of the road and turn off the engine.

The truth is that Check Engine light can be pointing to problems as simple as a loose gas cap. But it could be as serious as a severely misfiring engine.  Don't ignore it because it's there to help you avoid an expensive repair it is designed to alert you to, to tell you something's not quite right.

Your vehicle has a connected system of computers and sensors constantly checking to see that all systems are working the way they should. If something isn't, the system will turn on the Check Engine light.

If it's flashing, that could be serious. Look at some of the other warning lights or gauges such as heat or oil pressure. They could be telling you your vehicle's problem should be checked right away. In that case, if you can, safely pull off the road and shut the vehicle down. If your vehicle loses power and the Check Engine light is on, try not to push the demands you are making on the engine, such as towing or accelerating hard.

Simply put, a flashing Check Engine light should be checked out by a professional as soon as possible.

If the Check Engine light is on steadily, manufacturers say it means there's a problem, but it probably doesn't require immediate service.  The system is designed to remember the problem it found and store it (as a code) so it can be retrieved later.

When you do bring your vehicle in to have us see what's behind the Check Engine light coming on, we’ll hook your vehicle up to a diagnostics tool that can reveal the clues the engine's computers have stored.  It takes a trained technician to understand those clues, like a doctor who can interpret a patient's symptoms and come up with the correct diagnosis. Some newer vehicles can even be checked remotely.

Once we figure out the problem and repair it, you'll be back on the road again. It's nice to know the Check Engine light is your sentry, standing by to alert you the next time you begin to "see the light."

Madison Automotive
2457 Covington Pike
Memphis, TN 38128
(901)386-9600
http://www.madisonautomotive.net